21.2 Employer's responsibility
21.3 Dangerous incident reports
21.4 Blasting log
21.5 Authority to blast
21.6 Other legislation [Repealed]
21.11 Recording certificates
21.12 Custody of certificates
21.13 Suspension of duties
21.14 Submitting reports
21.15 Suspension of certificates
21.17 Worksite storage
21.19 Magazine condition
21.21 Separate handling
21.22 Vehicle operation
21.23 Flammable materials
21.24 Transportation of explosives
21.25 Mobile drill rigs
21.26 Water transport [Repealed]
21.27 Contact with metal
21.28 Emergency procedures
21.29 Safe operation
21.30 Vehicle load limit
21.31 Firefighting equipment
21.32 Trailer transportation
21.33 Railroad and highway crossings
21.34 Prior servicing
21.35 Overnight parking
21.37 Defective explosives
21.38 Cold temperatures
21.39 Abandoned explosives
21.40 Ignition sources prohibited
21.42 Predrilling requirements
21.43 Drilling prohibitions
21.44 Drill hole size
21.48 Loading tools
21.49 Electrical storms
21.50 Guarding loaded holes
21.52 Springing holes
21.53 Connecting detonating cord
21.54 Shock tubes
21.55 Pneumatic loading
21.56 Safety fuse assemblies
21.57 Lighting safety fuse
21.58 Stray currents
21.59 Extraneous currents
21.60 Static electricity
21.61 Radio frequency precautions
21.62 Mobile transmitters
21.63 Testing circuits
21.64 Capacity of blasting machines
21.65 Firing from power lines
21.66 Blaster's responsibility
21.67 Firing lines
21.68 Firing all holes
21.69 Blasting signals
21.70 Posting warning procedures
21.71 After the blast
21.72 Electrical blasting
21.74 Blast site examination
21.75 Unfired explosives
21.76 Removing loose material
21.77 Marking and detonating
21.78 Safety fuse reblast
21.79 No relighting
21.80 Drilling for refiring
21.81 Extracting explosives
21.82 Underwater blasting
21.83 Special effects blasting
21.84 Seismic blasting
21.85 Avalanche control
In this Part
"blaster" means a person who is the holder of a valid blaster's certificate issued by the Board or acceptable to the Board;
"blaster of record" means the blaster who is designated to be in charge of a blasting operation;
"blasting area" means an area extending at least 50 m (165 ft) in every direction from a place where explosive materials are being prepared or fixed, or where an unexploded charge is known or believed to exist;
"blasting log" means a written record of loading details, and the site examination after the blast;
"blasting operation" includes preparing, placing, and firing a charge, handling a misfire, and destroying or disposing of explosive materials;
"bootleg" means the remnant of a blast hole which did not properly break when the blast was initiated; also called socket, butt or button;
"charge" means explosive materials which may or may not contain a primer, and which are placed for the purpose of detonation;
"danger area" means an area in which there may be danger to persons or property from flying material or other hazardous condition resulting from a blast;
"dangerous incident" means an accident or near miss occurrence caused by or as a result of the use of explosives, and also includes an unexpected result or problem with explosive products;
"day box" means an unlicensed facility, not used for overnight storage, constructed to Type 6 magazine specifications pursuant to the Explosives Act (Canada);
"detonator" or "detonator products" includes those explosives commonly called blasting caps, or electric caps, or other similar devices used to detonate commercial explosives;
"explosive" means a substance that is made, manufactured or used to produce an explosion or detonation, including but not limited to blasting explosives, pyrotechnic devices and accessories containing explosives;
"igniter cord" means a small diameter wire coated with an incendiary composition used to ignite a series of safety fuse assemblies;
"isolated location" means an area where people other than the workers involved in the work project are not likely to be, and excludes frequently travelled roads, or a recreation area when it is likely to be used by people;
"magazine" means a structure used for the unattended storage of either detonators or explosives, and which meets the regulations and standards of the Explosives Act (Canada);
"misfire (mishole)" means a charge or part of a charge which, on initiation, failed to completely detonate or function, a dangerous condition;
"primer" means an explosive to which a detonator or other initiating device has been attached;
"safety fuse assembly" means a manufactured blasting accessory consisting of a precut length of safety fuse, an igniter cord connector, and a detonator;
"shunt" means a metal (aluminum or brass) clip or foil used to short out an electric detonator by interconnecting the leg wires, or means the act of shorting out leg wires by twisting them together;
"springing" means a blasting technique which opens up a pocket at the bottom of a blast hole so that successive larger charges may be loaded and blasted;
"stemming" means placing inert material in the portion between the top of the explosive column and the collar of a blast hole, intended to confine the explosive gases for an effective blast.
Nothing in this Part relieves an employer of the responsibility to provide adequate direction and instruction of workers, and to assign work only to those workers who are competent.
(1) If a blasting accident occurs which causes personal injury, or if there is any other dangerous incident involving explosives, whether or not there is personal injury, the employer must
(a) report the incident immediately to the Board, and
(b) forward a written report of the incident to the Board without undue delay.
(2) The written report of the incident must contain
(a) the date, time and location of the incident,
(b) the names and certificate numbers of all blasters involved,
(c) the names and occupations of any persons injured,
(d) the types of explosives, detonators, and blasting machine used,
(e) a factual account of events including the blaster's log records, and
(f) the action taken by the employer.
(1) The blaster of record must record in a log the preblast loading details and the results of the postblast site inspection.
(2) Blasting logs must be maintained at the blasting site, available for inspection by an officer, workers and worker representatives.
(3) The employer must ensure that blasting logs are kept for at least 5 years after completion of the blasting operation.
(4) The blaster must maintain a personal log of all blasting work that the blaster has performed.
(1) Only the holder of a valid blaster's certificate issued by the Board or acceptable to the Board is permitted to conduct or direct a blasting operation, and then only if the work involved is within the scope of that certificate.
(2) All work within the blasting area must be done under the authorization of the designated blaster of record responsible for that area.
(3) A blaster may be assisted by persons who do not hold blaster's certificates, but the blaster must have authority over the assistants and must exercise visual supervision over them and be responsible for their work during explosive loading, priming, fixing or firing.
Repealed. [B.C. Reg. 312/2003, effective October 29, 2003.]
A worker engaged in loading, unloading, or conveying explosives must be trained in the proper means for handling the explosives, the hazards of fire and mishandling and the procedures to follow in the event of a fire or explosion.
Back to Top
A candidate for a blaster's certificate must
(a) be at least 18 years of age,
(b) demonstrate a satisfactory knowledge of the English language, both written and spoken,
(c) be physically capable of safely carrying out the duties of a blaster, and
(d) forward written proof acceptable to the examining officer that
(i) the candidate has had at least 6 months experience in blasting operations as an assistant to a blaster, and/or
(ii) the candidate's character, knowledge, qualifications and experience would make the candidate competent to handle explosives.
Note: Blaster's certificates will normally be issued for a period of 5 years, and may be endorsed with any restriction that the Board deems necessary.
A person must not make, or assist in making, any false representation for the purpose of obtaining a blaster's certificate for any person.
Only persons authorized by the Board may conduct examinations for blaster's certificates.
The employer must ensure that the details on the certificate of a blaster are recorded and understood before permitting the certificate holder to carry out the duties of a blaster.
(1) A blaster must retain his or her certificate and must keep it in a safe place at the worksite while carrying out the duties of a blaster.
(2) The blaster's certificate must be produced for inspection on the request of an officer.
(3) A copy of a blaster's certificate is not acceptable as proof of certification.
If, in the opinion of the employer, the holder of a blaster's certificate has failed to comply with any of the blasting requirements in this Regulation, manufacturer's recommendations or recognized safe blasting practices, the employer must immediately investigate the incident and may suspend the blaster from performing the duties of a blaster.
The employer must submit to the Board a report of the investigation carried out under section 21.13.
An officer may seize and forward to the Board a blaster's certificate if there is reason to believe that the safety of any person may be or has been endangered by the blaster.
Note: Part 3 of the Workers Compensation Act gives authority to the Board to cancel or suspend a certificate or place other conditions on its use if the Board has reasonable grounds for believing that a person who holds a certificate has breached a term or condition of the certificate or has otherwise contravened Part 3 of the Act or this Regulation. When the Board has taken or is considering taking action under Part 3 of the Act, the person affected will be provided with an opportunity to make representation to the Board, and will be advised in writing of the reasons for any decision.
Back to Top
(1) Detonator products must not be kept in a store or receptacle in which explosives or safety fuses, fuse lighters, igniter cords or connectors are stored.
(2) At the loading site, detonator products must be stored separately from other explosives, and in a crush resistant box which is clearly identified.
Explosives at the worksite must be guarded or contained in secured day boxes until used or returned to storage magazines.
(1) The employer must ensure that the location of a magazine in which explosives are stored, and any restrictions on access or activity around the magazine area, are clearly communicated to all workers.
(2) A day box and receptacle used for day storage of explosives on a work site must, when they contain explosives, display signs indicating the presence of explosives in a conspicuous manner, and the signs must be removed when they are empty.
(3) A vehicle containing explosives while in a workplace must display signs indicating the presence of explosives in a conspicuous manner, visible from all sides of the vehicle, and the signs must be removed when the vehicle no longer contains explosives.
(1) The interior of an explosives magazine must be kept scrupulously clean and must be constructed, covered or lined to prevent the exposure of any ferrous metals or gritty materials.
(2) Precautions must be taken to exclude moisture from an explosives magazine.
(3) Any article or substance likely to cause a fire or explosion must be kept out of and at a safe distance from an explosives magazine.
(1) Detonating cord must be stored separately, or with explosives other than detonators.
(2) Igniter cord must be stored separately from fuses, detonators, or explosives.
Blasting explosives and detonator products must be kept and handled separately until the last most practicable moment, before bringing them together.
Back to Top
(1) A vehicle being used to transport explosives must be in sound mechanical condition, suitable for, and capable of, safely transporting explosives.
(2) Passengers, other than those assigned to assist in handling explosives, are not permitted on a vehicle transporting explosives.
Reasonable quantities of flammable or combustible materials may be carried by a conveyance transporting explosives at the workplace provided such materials are contained in a manner which will not cause or transmit a fire or explosion, and are adequately separated from any explosives containers on the conveyance.
(1) Explosives carried in a vehicle must be in a fully enclosed, locked, fire resistant fixed container or compartment, separate from the passenger compartment.
(2) Electric detonators must be transported in their original containers, with their leg wires shunted, as shipped by the manufacturer.
(3) Detonators must be adequately separated from other explosives during transport.
The transportation of explosives on a mobile drilling rig is only permitted if
(a) explosives and detonators are carried in separate containers built to type 6 or type 10 magazine standard and capacities, with 2 hooded locks, and
(b) the explosives and detonator containers are
(i) located at least 60 cm (2 ft) apart, with the doors or lids facing at least 90° apart,
(ii) located above the vehicle deck in a manner which protects the containers from contact with roadside objects and the drilling equipment,
(iii) located so the contents are not endangered by any heat source on the drill unit,
(iv) kept locked when outside the blasting area, and securely closed when in the blasting area, except when opened for depositing or removing their contents, and
(v) attended by the blaster of record, or a qualified person designated by the blaster, at all times when explosives are being carried.
[Amended by B.C. Reg. 188/2011, effective February 1, 2012.]
Repealed. [B.C. Reg. 312/2003, effective October 29, 2003.]
Contact between packages containing explosives and exposed ferrous metal in a conveyance must be prevented by the use of wood, tarpaulin, or other suitable dunnage materials.
Before explosives are transported, the employer must establish suitable written emergency procedures, and must ensure that all workers who may be affected are adequately instructed in the procedures.
A person operating a vehicle that is transporting explosives
(a) must operate the vehicle in a safe manner, consistent with prevailing road and weather conditions, and
(b) must not drive faster than 90 km/h (55 mph).
[Amended by B.C. Reg. 312/2003, effective October 29, 2003.]
A vehicle transporting explosives must not be operated or permitted to operate if the load to be transported exceeds 80% of the manufacturer's rated carrying capacity for the vehicle.
(1) A conveyance transporting explosives must be equipped with at least 2 fire extinguishers, of a type capable of quickly extinguishing gasoline, oil, or electrical fires.
(2) The fire extinguishers must be readily available for use and must have
(a) a minimum 5 BC rating for a vehicle with up to 2 000 kg (4 400 lbs) gross vehicle weight (GVW) rating, and
(b) a minimum 10 BC rating for a vehicle with more than 2 000 kg (4 400 lbs) GVW rating.
Explosives must not be transported in a trailer, or in any type of semitrailer unless it is equipped with power brakes operable from the tractor cab.
The operator of a vehicle transporting explosives must, before crossing
(a) a railroad track protected by an automatic signal device, reduce the speed of the vehicle and establish that the crossing can be made in safety, and
(b) a main highway, or a railroad track that is not protected by an automatic signal device, completely stop the vehicle and only proceed when the way is safely clear.
Explosives must not be loaded on or in a vehicle unless the vehicle has been fully serviced.
(1) When a vehicle carrying or containing explosives is to be parked overnight, the premises in which the vehicle will be parked must not be used for any other purpose which may involve any substance likely to cause explosion or fire.
(2) Such premises must be away from habitation and buildings that contain flammable materials.
(3) Repealed. [B.C. Reg. 312/2003, effective October 29, 2003.]
Back to Top
Explosive materials must be stored, transported, handled and used in the manner recommended by the manufacturer.
Explosive materials or accessories which have deteriorated, or are believed to be defective, must not be used and must be handled and disposed of in a safe manner following the manufacturer's recommendations.
If the sensitivity of an explosive is affected by cold temperatures the explosive may be brought to a working temperature in a manner recommended by the manufacturer, but must not be warmed near an open fire or a steam boiler nor by direct contact with steam or hot water.
Explosive materials and accessories must not be abandoned, but must be placed in suitable storage or disposed of in accordance with the manufacturer's instructions.
(1) Smoking is prohibited within 15 m (50 ft) of where explosives are stored, being handled, or are in loaded holes.
(2) Open flame ignition sources must not be permitted within 15 m (50 ft) of where explosives are stored, being handled, or are in loaded holes, unless the blaster of record gives consent.
(1) Containers, known or suspected to contain explosives or explosive residue, must be handled with care to prevent undue impact or exposure to excessive heat or flame.
(2) All empty explosives containers must be disposed of by burning or as recommended by the manufacturer.
Back to Top
Before drilling begins
(a) in a previously blasted area, the surface to be drilled must be exposed and examined for misfired explosives,
(b) faces or slopes must be cleared of loose material, or otherwise stabilized to prevent slides or falls of rock, and
(c) the location of utility services must be determined and clearly marked.
Drilling must not take place within
(a) 15 cm (6 in) of any part of a bootleg, or
(b) 6 m (20 ft) of any part of a hole containing explosives, unless prior written permission has been obtained from the Board.
Each drill hole to be loaded with explosives must be of sufficient diameter to permit free insertion of the explosives to the bottom of the hole without ramming, pounding, cutting, or undue pressure.
Back to Top
A primer must not be made up until immediately before placing the explosives.
Persons must not carry explosive materials in their clothing.
Wrappers must not be removed from cartridge explosives.
Explosives must not be loaded into a hole except with a loading tool made of wood, plastic or other non-sparking material.
If there is any sign of thunder or lightning storm activity, all blasting activity must be suspended and the danger area must be cleared and guarded if explosives are present at the blast site.
(1) Except as permitted by section 21.84, a hole which has been loaded, whether primed or not, but not fired by the end of the working day must not be left unattended.
(2) A worker, whose sole responsibility is the security of the explosives, must be posted to ensure that loaded holes are not tampered with while the work crew is absent from the site.
Except as permitted by section 21.84, a vehicle or other mechanized equipment must not be driven over a loaded hole.
After a hole is "sprung" ample time must be left for the hole to cool before further loading or placing of explosives or explosive accessories takes place.
(1) When detonating cords are used, the cords must only be interconnected or attached to trunk cords at the last most practicable moment after all holes are loaded.
(2) When detonating cords are used to prime a charge, the cord must be cut from the supply reel before, or as soon as possible after the charge is placed.
(3) Detonators or detonator connectors must not be attached to a detonating line until everything is in readiness for the blast.
(1) Non-electric shock tubes loaded into holes must not be pulled or snapped.
(2) Shock tube starters must not be fastened to the firing line until all holes are loaded and ready to be blasted.
(1) Explosives may only be loaded pneumatically if the procedures and equipment used will prevent buildup of static electricity or hazards from stray electric currents.
(2) Prior written permission of the Board must be obtained before any pneumatic loading is carried out at a hole which contains an electric detonator.
Back to Top
(1) Only safety fuse assemblies with antistatic protection may be used for safety fuse blasting.
(2) Safety fuse assemblies less than 1 m (3.3 ft) in length must not be used.
(3) Safety fuse assemblies must be handled with care to avoid pinching or kinking and damaged fuse assemblies must not be used.
(1) When lighting a single safety fuse assembly a match may be used.
(2) When multiple safety fuses are to be lit, a suitable safety fuse lighting device must be used to ensure that a minimum 90 cm (3 ft) fuse length safety factor is maintained.
(3) When multiple safety fuse assemblies are to be lit, a suitable lighting device, such as igniter cord, must be used, and once the igniter cord is lit the blast area must be vacated.
Back to Top
(1) Precautions must be taken to prevent premature detonation of electric detonators from sources of electricity.
(2) Blasting circuits must be kept on the ground with bare connections sufficiently elevated to prevent current leakage.
Electric detonators must not be used when extraneous current exceeds 50 milliamps.
(1) Precautions must be taken during handling of electric detonators to prevent premature detonation caused by static electricity.
(2) Detonator leg wires must not be thrown in the air or dragged along the ground.
(1) During electrical blasting, minimum distances from radio frequency transmitters as detailed in Institute of Makers of Explosives, Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators (Blasting Caps) Safety Library Publication No. 20, 1988 as amended from time to time, must be maintained.
(2) If the minimum distance has not otherwise been determined, electrical blasting circuits are not permitted within
(a) 100 m (330 ft) of a CB or other mobile or portable radio frequency transmitter, and
(b) 1 000 m (3,300 ft) of an AM, FM, TV, or other fixed radio frequency transmitter.
(1) If absolute control of radio frequency transmitters cannot be maintained, for example, on public highways, warning signs must be posted to alert vehicle operators to turn off their transmitters.
(2) When electrical circuits are being connected, traffic control persons must be posted to instruct vehicle operators to turn transmitters off.
Each electrical circuit must be tested before firing using an instrument acceptable to the Board, and the measured resistance must be recorded in the blasting log.
(1) Repealed. [B.C. Reg. 312/2003, effective October 29, 2003.]
(2) The capacity of a blasting machine must be clearly marked on the blasting machine and must not be exceeded.
[Amended by B.C. Reg. 312/2003, effective October 29, 2003.]
|* See also sections 4.1, 4.3, and 4.11 of the OHS Regulation.|
When firing is done from a power line, an approved blasting safety switch must be used, and the switch kept locked and inaccessible to anyone except the blaster.
Back to Top
(1) The blaster must take precautions for the protection of persons and property, including proper loading and stemming of holes, and where necessary, the use of cover for the blast or other effective means of controlling the blast or resultant flying material.
(2) The blaster must ensure that the danger area is clear of workers and is kept clear during the blasting period.
(3) The blaster must post workers who have the sole responsibility of guarding against entry into the danger area of the blast site, and the workers must be instructed as to their duties and responsibilities.
(4) Whistles, signs or other signals may not be used in place of the guards required by subsection (3).
(5) Before sounding the warning signals, the blaster must clear the danger area and post guards as required by subsections (2) to (4), and must ensure that all persons have reached a place of safety.
The firing lines must not be attached to the blasting machine or blasting circuit until all charges are placed, connected and ready to be fired.
(1) Charges must be fired in logical sequence.
(2) If any detonation could affect other charges placed nearby, all of the charges must be fired in one operation.
(1) The blaster must ensure that an audible signalling device, distinct from other signalling devices in the area, is used to give the following warning signals:
(a) preceding the blast, 12 short whistle signals must be sounded at one second intervals;
(b) two minutes must elapse after the last warning signal before initiating the blast;
(c) following the blast and after the area has been inspected and found safe, one prolonged whistle signal of at least 5 seconds duration must be sounded, to signify that permission is granted to return to the blasting area.
(2) Subsection (1) does not apply to avalanche control, single underground headings, buried seismic work in isolated locations or other circumstances deemed appropriate by the Board, in which case the blaster must ensure that alternative warning procedures acceptable to the Board are used.
(3) Subsection (1)(b) does not apply with respect to the 2 minute warning in congested areas if alternative warning procedures acceptable to the Board are developed and implemented.
The employer must ensure that the warning procedure and blasting signals to be used at the workplace are posted conspicuously at each blasting operation, and workers must be instructed in this information.
Back to Top
After a blast is detonated, the blaster must not allow any other worker to enter the blasting area until
(a) the area has been examined by the blaster for misfires and other hazards,
(b) the "all clear" has been sounded, and
(c) the blaster gives permission for work to proceed.
After a blast is electrically detonated the blaster must not enter the blasting area until
(a) the blaster has disconnected the firing cables from the blasting machine and has short circuited the lead wires, or
(b) if the blast was detonated from a power line, the blaster has disconnected the firing lines and locked the switch open.
Note: See section 21.84 for alternate procedures for seismic blasting operations.
(1) When a blast initiated by electrical methods cannot be verified to have completely detonated, or is suspected to have misfired, the blaster must disconnect the firing lines from the blasting machine, and wait at least 10 minutes before permitting anyone to enter the danger area.
(2) When a blast initiated by a safety fuse cannot be verified to have completely detonated, or is suspected to have misfired, the blaster must wait at least 30 minutes after the estimated time of detonation before permitting anyone to enter the danger area.
Back to Top
The blaster must make a thorough examination of the blast site after charges have been fired to determine that there are no unexploded charges remaining.
(1) If there is evidence or suspicion of misfired charges or undetonated explosives
(a) all loose unfired explosives must be collected and destroyed in a safe manner, and
(b) the blaster must direct the hand removal of as much broken material as possible before metallic tools or equipment are used.
(2) Metallic equipment must not be used during misfire procedures unless
(a) the blaster directs the use of the equipment,
(b) the area is adequately illuminated, and
(c) everyone, except the blaster and the equipment operator, is removed from the area.
(1) Removal of loose material must be done cautiously, with regard for possible undetonated explosive materials or misfired holes.
(2) Loose rock must be scaled from faces in the work area and the area stabilized before other work resumes.
(1) Each misfired charge must be clearly marked and the area cordoned off.
(2) No attempt must be made to remove an unexploded charge and no other work may take place within the blasting area, until the misfired charge has been successfully detonated by rewiring or repriming with a fresh primer.
If a misfired charge contains a safety fuse and is reblasted, workers must not return to the blast site until 30 minutes after the detonation.
Relighting a safety fuse is prohibited.
When drilling is necessary to expose a misfired charge the blaster must
(a) accurately determine the angle of the misfired hole,
(b) direct the angle and depth of the hole being drilled, and
(c) ensure that the hole being drilled is at least 60 cm (2 ft) from any part of the misfired charge.
(1) It is prohibited to extract, or attempt to extract, a primer or explosive of the nitroglycerine type from a loaded hole.
(2) Only if the hole does not contain a detonator may a blaster or person authorized by the blaster remove ammonium nitrate, water gel or emulsion type explosives from a blast hole, and the removal procedure must be carried out with caution, using moderate air or water pressure or a combination thereof, with a blowpipe made of non-metallic construction.
Back to Top
(1) Only explosives and blasting accessories recommended by the manufacturer for underwater blasting may be used for underwater blasting.
(2) Whenever explosive materials are being used in underwater blasting operations, a blasting flag (international code "Bravo", a solid red flag) must be displayed.
(3) Precautions must be taken to prevent damage to structures in the danger area.
(4) Underwater blasts must not be detonated when a diving operation or water craft is within the danger area, nor until the diving supervisor has given permission for the blaster to fire the charge.
(5) After detonating an underwater blast, the site must be examined by the blaster, or by a competent diver who
(a) has been instructed in the recognition of undetonated explosive materials and other blasting related hazards, and
(b) is under the direction of a blaster.
(6) The blaster must ensure that misfires are handled properly and that other blasting related hazards are removed.
Special effects blasting must be carried out under the direction of a blaster certified in this specialty to a standard acceptable to the Board.
(1) If seismic blasting is carried out in an isolated location, loaded holes may be left unattended only if
(a) the blaster has first ensured that all leg wires are shunted together, drill cuttings are spread out and levelled, the leg wires are coiled as close to the ground as possible while never exceeding 15 cm (6 in) above the ground level, and the holes are suitably user identified, and recorded in the blasting log, and
(b) the holes are blasted within 30 days.
(2) In seismic blasting, if the recorder can confirm complete detonation, the firing line may be left connected to the firing switch and disconnected at the hole.
(3) In a seismic blasting operation, a misfired or unfired charge may be left unfired only if
(a) it cannot be conventionally and safely detonated,
(b) it is in an isolated location,
(c) it is at a depth sufficient to minimize the risk of injury to workers or other persons,
(d) its location is effectively marked, and
(e) a permanent record of its location is kept.
[Enacted by B.C. Reg. 381/2004, effective January 1, 2005.]
(4) Seismic water tank trucks having open flame water heaters must not be used to transport explosives unless
(a) the distance between the heat tube and the outside of the tank is at least 35 cm (14 in),
(b) a heater, if woodburning, has a fire box of a type that fully contains the fuel and two dampers mounted in the heat tube, one at the vent end and the other at the fire box, so the flame may be shut in instantly in the event of an accident, and
(c) the detonator storage is located on the opposite side of the vehicle from the explosive magazine, and both are built to type 6 magazine standard.
(d) Repealed. [B.C. Reg. 312/2003, effective October 29, 2003.]
|* See sections 21.22 and 21.23 of the OHS Regulation.|
(5) In a seismic operation where there is no alternate route, a vehicle may be driven over a loaded hole if
(a) bypassing the hole is not practicable,
(b) operational planning minimizes the requirement to travel through a loaded area,
(c) safe work procedures are developed and communicated to all workers before they start work at the site,
(d) loaded holes are in compliance with subsection (1),
(e) explosive charges are at a minimum depth of 6 m (20 ft), and
(f) all radio transmission equipment is turned off, or the transmission capability is disabled by disconnecting the microphone.
Note: Some electrical equipment, such as cellular telephones and other types of mobile telephone equipment continuously transmit a radio signal when turned on, so such devices must be turned off when it is necessary to drive over a loaded hole.
(1) Explosive charges must not be placed manually on site by workers or projected by any means for the purpose of avalanche control, until the proposed work procedures have been submitted to and accepted by the Board.
(2) Explosives must not be primed until the last most practicable moment which means that point in time when the explosives are as close to the control route as possible, in a safe, sheltered location excluded from public access.
(3) The pull-wire lighter must not be placed on the safety fuse assembly until immediately before placing the charge.
(4) The employer must ensure that procedures are reviewed annually and that proposed changes to the procedures are submitted to the Board for approval before implementation.
[Amended by B.C. Reg. 312/2003, effective October 29, 2003.]
Back to Top